? 18553382068 13951158508
淄柴ZC330ZLC/S系列雙燃料發動機以ZC330系列柴油機為母型機，充分吸收國內外先進技術和設計思想，在保持其良好的動力性、經濟性、可靠性等優點的基礎上，設計開發了中速大功率ZC330ZLC/S系列LNG/柴油本質多點噴射雙燃料發動機。ZC330ZLC/S系列雙燃料發動機采用本質型設計，天然氣供氣系統在任何情況下機艙均處于狀態；采用國內準內混式燃氣電控多點噴射技術。發動機可以根據實際工況切換工作狀態，既可以使用LNG雙燃料工作，也可以單獨使用柴油工作。其通過電子控制單元實現燃氣與柴油噴射的比例，使發動機始終運行在狀態下，在不影響功率輸出的條件下節省柴油。部分負荷點燃油替代率可達到85%，滿負荷燃油替代率不低于70%。ZC330ZLC/S系列雙燃料發動機設計先進、結構合理、性能可靠、自動化程度高、維護方便、低油耗、低排放等優點，主要用于LNG運輸船、散貨船用主機或輔機?？蓾M足機旁操縱、遙控操縱及無人機艙的要求。
淄柴雙燃料控制系統簡介
更經濟：液化天然氣（LNG）供氣系統：主要由燃氣進氣管組件、波紋雙壁軟管組件、噴射閥組件組成，用來給發動機提供所需流量和壓力的氣體燃料。
更先進：燃氣控制系統：采用了代表世界海茵茨曼控制器MVC01-24及雙壁結構的燃氣噴射閥Megasol 250，燃氣控制及相關報警控制都滿足了船規，大大提高了燃氣系統的及發動機自身保障，這在國內的應用均屬首例?？刂葡到y(tǒng)原理圖如下頁表：
更智能：
電子控制調速系統：采用了調速執行器RE2800與控制器的搭配，海茵茨曼電子控制器MVC 01-24輸出0~1A調速信號到RE2800內置電磁線圈，由電磁線圈產生電磁力大小來控制RE2800的輸出供油量大小，進而有效的控制了發動機的柴油供給，對發動機燃氣高替代率的實現提供了技術保障。相比較于傳統機械液壓調速器，RE2800電子液壓調速器的扭力大、可靠性高，集成了海茵茨曼電子控制器的優勢，調速性能及控制精度屬于比較高水平。調速器現大量應用于MAN的2131機型上，技術成熟可靠。
更可靠：
燃氣進氣系統：燃氣噴射閥采用雙壁管結構。燃氣進氣主管及支管采用雙壁管結構，體積小，安 全系數高。
ZC6330ZLC/S雙燃料發動機技術參數
| 序號No | 名稱 ltem | 單位Unit | 技術 規 格 Technical specifications | |||
| 1 | 型式 Model | 直列、四沖程、直噴、渦輪增壓、不可逆轉 In-line, four strokes, direct injection turbocharger, irreversiblea | ||||
| 2 | 型號 Type | ZC6330ZLC/S-10 | ZC6330ZLC/S-4 | ZC6330ZLC/S-5 | ZC6330ZLC/S-6 | |
| 3 | 持續功率 Rated power | kW/PS | 2756/3750 | 2574/3500 | 2427/3300 | 2207/3000 |
| 4 | 持續轉速 Rated speed | rpm | 640 | 620 | ||
| 5 | 氣缸直徑 Cylinder bore | mm | 330 | |||
| 6 | 活塞行程 Piston stroke | mm | 440 | |||
| 7 | 氣缸數 No. of cylinders | 6 | ||||
| 8 | 總排量 Total displacement | L | 225.8 | |||
| 9 | 壓縮比 Compression ratio | / | 13.5 | |||
| 10 | 工作穩定轉速Minimum stable speed | rpm | 256 | 248 | ||
| 11 | 活塞平均速度 Mean piston speed | m/s | 9.39 | 9.09 | ||
| 12 | 平均有效壓力 Mean effective pressure | MPa | 2.29 | 2.206 | 2.081 | 1.89 |
| 13 | 平均指示壓力 Mean indicated pressure | MPa | 2.489 | 2.398 | 2.262 | 2.057 |
| 14 | 增壓壓力 Supercharging pressure | MPa | 0.40±0.03 | 0.35±0.03 | ||
| 15 | 爆發壓力 Maximum explosion pressure | MPa | ≤17.5 | ≤17.0 | ||
| 16 | 各缸排氣溫度 Each cylinder exhaust temperature | ℃ | ≤450 | |||
| 17 | 渦輪前排溫 Exhaust temperature before turbocharger | ℃ | ≤600 | |||
| 18 | 燃油消耗率 Fuel oil consumption | g/kw·h | 190+5% | |||
| 19 | 機油消耗率 Lubrication oil consumption | g/kw·h | 1.1 在持續工況下 | |||
| 20 | 曲柄排列 Crank arrangement | / | 1.6 2.5 3.4 | |||
| 21 | 發火順序 Fire order | / | 1-2-4-6-5-3(順時針 Clockwise) | |||
| 22 | 起動方式 Starting method | 壓縮空氣起動 Compressed air starting motor | ||||
| 23 | 供油正時 Fuel injection timing | ℃A | 上死點前10~13.5 | |||
| 24 | 起動空氣壓力 Starting air pressure | MPa | 起動壓力Max. starting pressure:2.94MPa, 起動壓力Min. starting air: 1.1MPa | |||
| 25 | 天然氣工作壓力Maximum work pressure | MPa | 0.48 | 0.43 | ||
| 26 | 外形尺寸 Dimensions(L×W×H) | mm | 5761.7×2442×3867 | |||
| 27 | 活塞吊出高度 The lifting height of piston | mm | 3223 | |||
| 28 | 缸套吊出高度 The lifting height of cylinder liner | mm | 3608 | |||
| 29 | 整機質量 Weight | kg | 34450 | |||
| 序號No | 名稱 ltem | 單位Unit | 技 術 規格 Technical specifications | |||
| 1 | 型式 Model | 直列、四沖程、直噴、渦輪增壓、不可逆轉 In-line, four strokes, direct injection turbocharger, irreversiblea | ||||
| 2 | 型號 Type | ZC6330ZLC/S-9ZC6330ZLC/S-7ZC6330ZLC/S-8ZC6330ZLC/S-11 | ||||
| 3 | 持續功率 Rated power | kW/PS | 2242/30501838/25001470/20002646/3600 | |||
| 4 | 持續轉速 Rated speed | rpm | 600 | |||
| 5 | 氣缸直徑 Cylinder bore | mm | 330 | |||
| 6 | 活塞行程 Piston stroke | mm | 440 | |||
| 7 | 氣缸數. No. of cylinders | 6 | ||||
| 8 | 總排量 Total displacement | L | 225.8 | |||
| 9 | 壓縮比 Compression ratio | / | 13.5 | |||
| 10 | 工作穩定轉速 Minimum stable speed | rpm | 240 | |||
| 11 | 活塞平均速度 Mean piston speed | m/s | 8.8 | |||
| 12 | 平均有效壓力 Mean effective pressure | MPa | 1.987 | 1.575 | 1.259 | 2.268 |
| 13 | 平均指示壓力 Mean indicated pressure | MPa | 2.160 | 1.712 | 1.368 | 2.465 |
| 14 | 增壓壓力 Supercharging pressure | MPa | 0.35±0.03 | 0.28±0.03 | 0.40±0.03 | |
| 15 | 爆發壓力 Maximum explosion pressure | MPa | ≤17.0 | ≤15.0 | ≤17.5 | |
| 16 | 各缸排氣溫度 Each cylinder exhaust temperature | ℃ | ≤450 | |||
| 17 | 渦輪前排溫 Exhaust temperature before turbocharger | ℃ | ≤600 | |||
| 18 | 燃油消耗率 Fuel oil consumption | g/kw·h | 190+5% | |||
| 19 | 機油消耗率 Lubrication oil consumption | g/kw·h | 1.1 在持續工況下 | |||
| 20 | 曲柄排列 Crank arrangement | / | 1.6 2.5 3.4 | |||
| 21 | 發火順序 Fire order | / | 1-2-4-6-5-3(順時針 Clockwise) | |||
| 22 | 起動方式 Starting method | 壓縮空氣起動 Compressed air starting motor | ||||
| 23 | 供油正時 Fuel injection timing | ℃A | 上死點前10~13.5 | |||
| 24 | 起動空氣壓力 Starting air pressure | MPa | 起動壓力Max. starting pressure:2.94MPa, 起動壓力Min. starting air: 1.1MPa | |||
| 25 | 天然氣工作壓力 Maximum work pressure | MPa | 0.48 | 0.43 | 0.48 | |
| 26 | 外形尺寸 Dimensions(L×W×H) | mm | 5761.7×2442×3867 | |||
| 27 | 活塞吊出高度 The lifting height of piston | mm | 3223 | |||
| 28 | 缸套吊出高度 The lifting height of cylinder liner | mm | 3608 | |||
| 29 | 整機質量 Weight | kg | 34450 | |||
ZC8330ZLC/S雙燃料發動機技術參數
| 序號No | 名稱 ltem | 單位Unit | 技 術 規 格 Technical specifications | |||
| 1 | 型式 Model | 直列、四沖程、直噴、渦輪增壓、不可逆轉 In-line, four strokes, direct injection turbocharger, irreversiblea | ||||
| 2 | 型號 Type | ZC8330ZLC/S-9 | ZC8330ZLC/S-4 | ZC8330ZLC/S-5 | ZC8330ZLC/S-6 | |
| 3 | 持續功率 Rated power | kW/PS | 3675/5000 | 3310/4500 | 3163/4300 | 2942/4000 |
| 4 | 持續轉速 Rated speed | rpm | 640 | 620 | ||
| 5 | 氣缸直徑 Cylinder bore | mm | 330 | |||
| 6 | 活塞行程 Piston stroke | mm | 440 | |||
| 7 | 氣缸數. No. of cylinders | 6 | ||||
| 8 | 總排量 Total displacement | L | 301.1 | |||
| 9 | 壓縮比 Compression ratio | / | 13.5 | |||
| 10 | 工作穩定轉速Minimum stable speed | rpm | 256 | 248 | ||
| 11 | 活塞平均速度 Mean piston speed | m/s | 9.39 | 9.09 | ||
| 12 | 平均有效壓力 Mean effective pressure | MPa | 2.287 | 2.128 | 2.033 | 1.892 |
| 13 | 平均指示壓力 Mean indicated pressure | MPa | 2.486 | 2.313 | 2.210 | 2.057 |
| 14 | 增壓壓力 Supercharging pressure | MPa | 0.40±0.03 | 0.35±0.03 | ||
| 15 | 爆發壓力 Maximum explosion pressure | MPa | ≤17.5 | ≤17.0 | ||
| 16 | 各缸排氣溫度 Each cylinder exhaust temperature | ℃ | ≤450 | |||
| 17 | 渦輪前排溫 Exhaust temperature before turbocharger | ℃ | ≤600 | |||
| 18 | 燃油消耗率 Fuel oil consumption | g/kw·h | 190+5% | |||
| 19 | 機油消耗率 Lubrication oil consumption | g/kw·h | 1.1 在持續工況下 | |||
| 20 | 曲柄排列 Crank arrangement | / | 1.8 4.5 + 3.6 2.7 | |||
| 21 | 發火順序Fire order | / | 1-4-7-6-8-5-2-3(順時針 Clockwise) | |||
| 22 | 起動方式 Starting method | 壓縮空氣起動 Compressed air starting motor | ||||
| 23 | 供油正時 Fuel injection timing | ℃A | 上死點前10~13.5 | |||
| 24 | 起動空氣壓力 Starting air pressure | MPa | 起動壓力Max. starting pressure:2.94MPa,起動壓力Min. starting air: 1.1MPa | |||
| 25 | 天然氣工作壓力Maximum work pressure | MPa | 0.48 | 0.43 | ||
| 26 | 外形尺寸 Dimensions(L×W×H) | mm | 6801.7×1977×3556.5 | |||
| 27 | 活塞吊出高度 The lifting height of piston | mm | 3223 | |||
| 28 | 缸套吊出高度 The lifting height of cylinder liner | mm | 3608 | |||
| 29 | 整機質量 Weight | kg | 約43000 | |||
| 序號No | 名稱 ltem | 單位Unit | 技術 規 格 Technical specifications | |||
| 1 | 型式 Model | 直列、四沖程、直噴、渦輪增壓、不可逆轉 In-line, four strokes, direct injection turbocharger, irreversiblea | ||||
| 2 | 型號 Type | ZC8330ZLC/S-1 | ZC8330ZLC/S-7 | ZC8330ZLC/S-8 | ZC8330ZLC/S-15 | |
| 3 | 持續功率 Rated power | kW/PS | 2977/4050 | 2427/3300 | 1912/2600 | 3310/4500 |
| 4 | 持續轉速 Rated speed | rpm | 600 | |||
| 5 | 氣缸直徑 Cylinder bore | mm | 330 | |||
| 6 | 活塞行程 Piston stroke | mm | 440 | |||
| 7 | 氣缸數 No. of cylinders | 8 | ||||
| 8 | 總排量 Total displacement | L | 301.1 | |||
| 9 | 壓縮比 Compression ratio | / | 13.5 | |||
| 10 | 工作穩定轉速Minimum stable speed | rpm | 240 | |||
| 11 | 活塞平均速度 Mean piston speed | m/s | 8.8 | |||
| 12 | 平均有效壓力 Mean effective pressure | MPa | 1.979 | 1.27 | 1.612 | 2.199 |
| 13 | 平均指示壓力 Mean indicated pressure | MPa | 2.151 | 1.380 | 1.752 | 2.390 |
| 14 | 增壓壓力 Supercharging pressure | MPa | 0.35±0.03 | 0.28±0.03 | 0.35±0.03 | |
| 15 | 爆發壓力 Maximum explosion pressure | MPa | ≤17.0 | ≤15.0 | ≤17.0 | |
| 16 | 各缸排氣溫度 Each cylinder exhaust temperature | ℃ | ≤450 | |||
| 17 | 渦輪前排溫 Exhaust temperature before turbocharger | ℃ | ≤600 | |||
| 18 | 燃油消耗率 Fuel oil consumption | g/kw·h | 190+5% | |||
| 19 | 機油消耗率 Lubrication oil consumption | g/kw·h | 1.1 在持續工況下 | |||
| 20 | 曲柄排列 Crank arrangement | / | 1.8 4.5 + 3.6 2.7 | |||
| 21 | 發火順序 Fire order | / | 1-4-7-6-8-5-2-3(順時針 Clockwise) | |||
| 22 | 起動方式 Starting method | 壓縮空氣起動 Compressed air starting motor | ||||
| 23 | 供油正時 Fuel injection timing | ℃A | 上死點前10~13.5 | |||
| 24 | 起動空氣壓力 Starting air pressure | MPa | 起動壓力Max. starting pressure:2.94MPa, 起動壓力Min. starting air: 1.1MPa | |||
| 25 | 天然氣工作壓力Maximum work pressure | MPa | 0.43 | 0.36 | 0.48 | |
| 26 | 外形尺寸 Dimensions(L×W×H) | mm | 6801.7×1977×3556.5 | |||
| 27 | 活塞吊出高度 The lifting height of piston | mm | 3223 | |||
| 28 | 缸套吊出高度 The lifting height of cylinder liner | mm | 3608 | |||
| 29 | 整機質量Weight | kg | 約43000 | |||
淄柴ZC330ZLC/S系列雙燃料發動機以ZC330系列柴油機為母型機，充分吸收國內外先進技術和設計思想，在保持其良好的動力性、經濟性、可靠性等優點的基礎上，設計開發了中速大功率ZC330ZLC/S系列LNG/柴油本質多點噴射雙燃料發動機。ZC330ZLC/S系列雙燃料發動機采用本質型設計，天然氣供氣系統在任何情況下機艙均處于狀態；采用國內準內混式燃氣電控多點噴射技術。發動機可以根據實際工況切換工作狀態，既可以使用LNG雙燃料工作，也可以單獨使用柴油工作。其通過電子控制單元實現燃氣與柴油噴射的比例，使發動機始終運行在狀態下，在不影響功率輸出的條件下節省柴油。部分負荷點燃油替代率可達到85%，滿負荷燃油替代率不低于70%。ZC330ZLC/S系列雙燃料發動機設計先進、結構合理、性能可靠、自動化程度高、維護方便、低油耗、低排放等優點，主要用于LNG運輸船、散貨船用主機或輔機?？蓾M足機旁操縱、遙控操縱及無人機艙的要求。
淄柴雙燃料控制系統簡介
更經濟：液化天然氣（LNG）供氣系統：主要由燃氣進氣管組件、波紋雙壁軟管組件、噴射閥組件組成，用來給發動機提供所需流量和壓力的氣體燃料。
更先進：燃氣控制系統：采用了代表世界海茵茨曼控制器MVC01-24及雙壁結構的燃氣噴射閥Megasol 250，燃氣控制及相關報警控制都滿足了船規，大大提高了燃氣系統的及發動機自身保障，這在國內的應用均屬首例?？刂葡到y(tǒng)原理圖如下頁表：
更智能：
電子控制調速系統：采用了調速執行器RE2800與控制器的搭配，海茵茨曼電子控制器MVC 01-24輸出0~1A調速信號到RE2800內置電磁線圈，由電磁線圈產生電磁力大小來控制RE2800的輸出供油量大小，進而有效的控制了發動機的柴油供給，對發動機燃氣高替代率的實現提供了技術保障。相比較于傳統機械液壓調速器，RE2800電子液壓調速器的扭力大、可靠性高，集成了海茵茨曼電子控制器的優勢，調速性能及控制精度屬于比較高水平。調速器現大量應用于MAN的2131機型上，技術成熟可靠。
更可靠：
燃氣進氣系統：燃氣噴射閥采用雙壁管結構。燃氣進氣主管及支管采用雙壁管結構，體積小，安 全系數高。
ZC6330ZLC/S雙燃料發動機技術參數
| 序號No | 名稱 ltem | 單位Unit | 技術 規 格 Technical specifications | |||
| 1 | 型式 Model | 直列、四沖程、直噴、渦輪增壓、不可逆轉 In-line, four strokes, direct injection turbocharger, irreversiblea | ||||
| 2 | 型號 Type | ZC6330ZLC/S-10 | ZC6330ZLC/S-4 | ZC6330ZLC/S-5 | ZC6330ZLC/S-6 | |
| 3 | 持續功率 Rated power | kW/PS | 2756/3750 | 2574/3500 | 2427/3300 | 2207/3000 |
| 4 | 持續轉速 Rated speed | rpm | 640 | 620 | ||
| 5 | 氣缸直徑 Cylinder bore | mm | 330 | |||
| 6 | 活塞行程 Piston stroke | mm | 440 | |||
| 7 | 氣缸數 No. of cylinders | 6 | ||||
| 8 | 總排量 Total displacement | L | 225.8 | |||
| 9 | 壓縮比 Compression ratio | / | 13.5 | |||
| 10 | 工作穩定轉速Minimum stable speed | rpm | 256 | 248 | ||
| 11 | 活塞平均速度 Mean piston speed | m/s | 9.39 | 9.09 | ||
| 12 | 平均有效壓力 Mean effective pressure | MPa | 2.29 | 2.206 | 2.081 | 1.89 |
| 13 | 平均指示壓力 Mean indicated pressure | MPa | 2.489 | 2.398 | 2.262 | 2.057 |
| 14 | 增壓壓力 Supercharging pressure | MPa | 0.40±0.03 | 0.35±0.03 | ||
| 15 | 爆發壓力 Maximum explosion pressure | MPa | ≤17.5 | ≤17.0 | ||
| 16 | 各缸排氣溫度 Each cylinder exhaust temperature | ℃ | ≤450 | |||
| 17 | 渦輪前排溫 Exhaust temperature before turbocharger | ℃ | ≤600 | |||
| 18 | 燃油消耗率 Fuel oil consumption | g/kw·h | 190+5% | |||
| 19 | 機油消耗率 Lubrication oil consumption | g/kw·h | 1.1 在持續工況下 | |||
| 20 | 曲柄排列 Crank arrangement | / | 1.6 2.5 3.4 | |||
| 21 | 發火順序 Fire order | / | 1-2-4-6-5-3(順時針 Clockwise) | |||
| 22 | 起動方式 Starting method | 壓縮空氣起動 Compressed air starting motor | ||||
| 23 | 供油正時 Fuel injection timing | ℃A | 上死點前10~13.5 | |||
| 24 | 起動空氣壓力 Starting air pressure | MPa | 起動壓力Max. starting pressure:2.94MPa, 起動壓力Min. starting air: 1.1MPa | |||
| 25 | 天然氣工作壓力Maximum work pressure | MPa | 0.48 | 0.43 | ||
| 26 | 外形尺寸 Dimensions(L×W×H) | mm | 5761.7×2442×3867 | |||
| 27 | 活塞吊出高度 The lifting height of piston | mm | 3223 | |||
| 28 | 缸套吊出高度 The lifting height of cylinder liner | mm | 3608 | |||
| 29 | 整機質量 Weight | kg | 34450 | |||
| 序號No | 名稱 ltem | 單位Unit | 技 術 規格 Technical specifications | |||
| 1 | 型式 Model | 直列、四沖程、直噴、渦輪增壓、不可逆轉 In-line, four strokes, direct injection turbocharger, irreversiblea | ||||
| 2 | 型號 Type | ZC6330ZLC/S-9ZC6330ZLC/S-7ZC6330ZLC/S-8ZC6330ZLC/S-11 | ||||
| 3 | 持續功率 Rated power | kW/PS | 2242/30501838/25001470/20002646/3600 | |||
| 4 | 持續轉速 Rated speed | rpm | 600 | |||
| 5 | 氣缸直徑 Cylinder bore | mm | 330 | |||
| 6 | 活塞行程 Piston stroke | mm | 440 | |||
| 7 | 氣缸數. No. of cylinders | 6 | ||||
| 8 | 總排量 Total displacement | L | 225.8 | |||
| 9 | 壓縮比 Compression ratio | / | 13.5 | |||
| 10 | 工作穩定轉速 Minimum stable speed | rpm | 240 | |||
| 11 | 活塞平均速度 Mean piston speed | m/s | 8.8 | |||
| 12 | 平均有效壓力 Mean effective pressure | MPa | 1.987 | 1.575 | 1.259 | 2.268 |
| 13 | 平均指示壓力 Mean indicated pressure | MPa | 2.160 | 1.712 | 1.368 | 2.465 |
| 14 | 增壓壓力 Supercharging pressure | MPa | 0.35±0.03 | 0.28±0.03 | 0.40±0.03 | |
| 15 | 爆發壓力 Maximum explosion pressure | MPa | ≤17.0 | ≤15.0 | ≤17.5 | |
| 16 | 各缸排氣溫度 Each cylinder exhaust temperature | ℃ | ≤450 | |||
| 17 | 渦輪前排溫 Exhaust temperature before turbocharger | ℃ | ≤600 | |||
| 18 | 燃油消耗率 Fuel oil consumption | g/kw·h | 190+5% | |||
| 19 | 機油消耗率 Lubrication oil consumption | g/kw·h | 1.1 在持續工況下 | |||
| 20 | 曲柄排列 Crank arrangement | / | 1.6 2.5 3.4 | |||
| 21 | 發火順序 Fire order | / | 1-2-4-6-5-3(順時針 Clockwise) | |||
| 22 | 起動方式 Starting method | 壓縮空氣起動 Compressed air starting motor | ||||
| 23 | 供油正時 Fuel injection timing | ℃A | 上死點前10~13.5 | |||
| 24 | 起動空氣壓力 Starting air pressure | MPa | 起動壓力Max. starting pressure:2.94MPa, 起動壓力Min. starting air: 1.1MPa | |||
| 25 | 天然氣工作壓力 Maximum work pressure | MPa | 0.48 | 0.43 | 0.48 | |
| 26 | 外形尺寸 Dimensions(L×W×H) | mm | 5761.7×2442×3867 | |||
| 27 | 活塞吊出高度 The lifting height of piston | mm | 3223 | |||
| 28 | 缸套吊出高度 The lifting height of cylinder liner | mm | 3608 | |||
| 29 | 整機質量 Weight | kg | 34450 | |||
ZC8330ZLC/S雙燃料發動機技術參數
| 序號No | 名稱 ltem | 單位Unit | 技 術 規 格 Technical specifications | |||
| 1 | 型式 Model | 直列、四沖程、直噴、渦輪增壓、不可逆轉 In-line, four strokes, direct injection turbocharger, irreversiblea | ||||
| 2 | 型號 Type | ZC8330ZLC/S-9 | ZC8330ZLC/S-4 | ZC8330ZLC/S-5 | ZC8330ZLC/S-6 | |
| 3 | 持續功率 Rated power | kW/PS | 3675/5000 | 3310/4500 | 3163/4300 | 2942/4000 |
| 4 | 持續轉速 Rated speed | rpm | 640 | 620 | ||
| 5 | 氣缸直徑 Cylinder bore | mm | 330 | |||
| 6 | 活塞行程 Piston stroke | mm | 440 | |||
| 7 | 氣缸數. No. of cylinders | 6 | ||||
| 8 | 總排量 Total displacement | L | 301.1 | |||
| 9 | 壓縮比 Compression ratio | / | 13.5 | |||
| 10 | 工作穩定轉速Minimum stable speed | rpm | 256 | 248 | ||
| 11 | 活塞平均速度 Mean piston speed | m/s | 9.39 | 9.09 | ||
| 12 | 平均有效壓力 Mean effective pressure | MPa | 2.287 | 2.128 | 2.033 | 1.892 |
| 13 | 平均指示壓力 Mean indicated pressure | MPa | 2.486 | 2.313 | 2.210 | 2.057 |
| 14 | 增壓壓力 Supercharging pressure | MPa | 0.40±0.03 | 0.35±0.03 | ||
| 15 | 爆發壓力 Maximum explosion pressure | MPa | ≤17.5 | ≤17.0 | ||
| 16 | 各缸排氣溫度 Each cylinder exhaust temperature | ℃ | ≤450 | |||
| 17 | 渦輪前排溫 Exhaust temperature before turbocharger | ℃ | ≤600 | |||
| 18 | 燃油消耗率 Fuel oil consumption | g/kw·h | 190+5% | |||
| 19 | 機油消耗率 Lubrication oil consumption | g/kw·h | 1.1 在持續工況下 | |||
| 20 | 曲柄排列 Crank arrangement | / | 1.8 4.5 + 3.6 2.7 | |||
| 21 | 發火順序Fire order | / | 1-4-7-6-8-5-2-3(順時針 Clockwise) | |||
| 22 | 起動方式 Starting method | 壓縮空氣起動 Compressed air starting motor | ||||
| 23 | 供油正時 Fuel injection timing | ℃A | 上死點前10~13.5 | |||
| 24 | 起動空氣壓力 Starting air pressure | MPa | 起動壓力Max. starting pressure:2.94MPa,起動壓力Min. starting air: 1.1MPa | |||
| 25 | 天然氣工作壓力Maximum work pressure | MPa | 0.48 | 0.43 | ||
| 26 | 外形尺寸 Dimensions(L×W×H) | mm | 6801.7×1977×3556.5 | |||
| 27 | 活塞吊出高度 The lifting height of piston | mm | 3223 | |||
| 28 | 缸套吊出高度 The lifting height of cylinder liner | mm | 3608 | |||
| 29 | 整機質量 Weight | kg | 約43000 | |||
| 序號No | 名稱 ltem | 單位Unit | 技術 規 格 Technical specifications | |||
| 1 | 型式 Model | 直列、四沖程、直噴、渦輪增壓、不可逆轉 In-line, four strokes, direct injection turbocharger, irreversiblea | ||||
| 2 | 型號 Type | ZC8330ZLC/S-1 | ZC8330ZLC/S-7 | ZC8330ZLC/S-8 | ZC8330ZLC/S-15 | |
| 3 | 持續功率 Rated power | kW/PS | 2977/4050 | 2427/3300 | 1912/2600 | 3310/4500 |
| 4 | 持續轉速 Rated speed | rpm | 600 | |||
| 5 | 氣缸直徑 Cylinder bore | mm | 330 | |||
| 6 | 活塞行程 Piston stroke | mm | 440 | |||
| 7 | 氣缸數 No. of cylinders | 8 | ||||
| 8 | 總排量 Total displacement | L | 301.1 | |||
| 9 | 壓縮比 Compression ratio | / | 13.5 | |||
| 10 | 工作穩定轉速Minimum stable speed | rpm | 240 | |||
| 11 | 活塞平均速度 Mean piston speed | m/s | 8.8 | |||
| 12 | 平均有效壓力 Mean effective pressure | MPa | 1.979 | 1.27 | 1.612 | 2.199 |
| 13 | 平均指示壓力 Mean indicated pressure | MPa | 2.151 | 1.380 | 1.752 | 2.390 |
| 14 | 增壓壓力 Supercharging pressure | MPa | 0.35±0.03 | 0.28±0.03 | 0.35±0.03 | |
| 15 | 爆發壓力 Maximum explosion pressure | MPa | ≤17.0 | ≤15.0 | ≤17.0 | |
| 16 | 各缸排氣溫度 Each cylinder exhaust temperature | ℃ | ≤450 | |||
| 17 | 渦輪前排溫 Exhaust temperature before turbocharger | ℃ | ≤600 | |||
| 18 | 燃油消耗率 Fuel oil consumption | g/kw·h | 190+5% | |||
| 19 | 機油消耗率 Lubrication oil consumption | g/kw·h | 1.1 在持續工況下 | |||
| 20 | 曲柄排列 Crank arrangement | / | 1.8 4.5 + 3.6 2.7 | |||
| 21 | 發火順序 Fire order | / | 1-4-7-6-8-5-2-3(順時針 Clockwise) | |||
| 22 | 起動方式 Starting method | 壓縮空氣起動 Compressed air starting motor | ||||
| 23 | 供油正時 Fuel injection timing | ℃A | 上死點前10~13.5 | |||
| 24 | 起動空氣壓力 Starting air pressure | MPa | 起動壓力Max. starting pressure:2.94MPa, 起動壓力Min. starting air: 1.1MPa | |||
| 25 | 天然氣工作壓力Maximum work pressure | MPa | 0.43 | 0.36 | 0.48 | |
| 26 | 外形尺寸 Dimensions(L×W×H) | mm | 6801.7×1977×3556.5 | |||
| 27 | 活塞吊出高度 The lifting height of piston | mm | 3223 | |||
| 28 | 缸套吊出高度 The lifting height of cylinder liner | mm | 3608 | |||
| 29 | 整機質量Weight | kg | 約43000 | |||
